HO Gooseneck Light Kit - NK015

 

 

Description Notes
Diagonal (side) cutters 1
6" Ruler with at least 1/16" increments 1
Dremel tool with sanding disks 1
# 80 drill bit 1
Access to drill press (used to punch holes in lampshades)
(alternate method can use a small mallet or hammer)
2
# 77 drill bit 2
Pin Vise - we recommend Starrett 162-A (0-.040" opening) 1
Small sheet (approx. 1"x 2"x 1/8" thk) styrene, brass or aluminum   2
1/8" drill bit 3
1/8" diameter pins or aluminum or brass tubing 3
1/2" x 1/2" x 2" (approx.) metal or plastic block 3
Straight pin or needle (for flaring end of tube) 4
Matches, candle or small torch (for heating end of tube) 4
Fine grade steel wool (handy for tube cleaning) 4
2-part 5-minute or 2-ton Epoxy (any Hardware store) 5
Toothpicks & aluminum foil )to mix epoxy with/on) 5
Isopropyl or Denatured Alcohol (for parts cleaning)  
CA Adhesive (super glue)  
35-45 watt soldering iron (for wire preparation) 6
Lower temp soldering iron (12-15 watt for LED soldering) 7
Bench vise  
Magnifiers & good workbench lighting  

 

 

 

 

 

 

 

 

 

 

Notes:

1. These tools will be used to cut the tubing and finish the ends. Details of this procedure can be found here.

2. These are used for punching holes in the lampshades. This procedure can be reviewed by clicking here.

3. Using internal tubing support (click here for details), these items can make tube bending fixture for accurate bending (drawing included with kit instructions. We also have this fixture available for purchase. More information can be found here.

4. Flaring of tube end is for lampshade support and bonding. This procedure can be reviewed here.

5. Two-part epoxy is preferred over CA adhesive for affixing lampshades to tubing. This procedure can be reviewed here

6. This soldering iron is used for pretinning the N5038 magnet wire (included in kit). This procedure can be reviewed here.

7. A low-temperature iron is used to solder the wires to the LEDs. This procedure can be reviewed here.

8. Threading the LED wires through the formed gooseneck tubing can be a challenging task. We have a new simplified method that makes the process easier. This procedure can be reviewed here.

 

 

The photos on the left show additional views of the gooseneck building lights that can be built with the parts in this kit.

Following is a list of tools and supplies that will be required to build the streetlights. This list also is included with the kit.

Item# Description Qty.
N7005 HO 18" Lampshade 8
N7006 HO Escutcheon (wall plate) 8
N2018 0.018" Stainless Steel Tubing x 9" long 2
N2112 0.012"  Stainless Wire x 9" long 4
N5038 #38 magnet Wire red & green 100 ft. each 1
N1011 or N1015 Micro white or yellow-white LED 8 or 4+4
NB4530 453-ohm 1/4-watt resistor (for 12-volt DC operation) 10

2012 Ngineering

Note:
This kit includes LED current protection resistors for use with a 12-volt DC power source. If separate DC power is not available, we highly recommend our versatile NK218 LED Power Kit for $26.75.

Details and a link for purchasing the NK218 can be found by clicking here.

An itemized list of parts included in the kit is as follows:

Gooseneck lamp with (modern era) white LED above or (early era) yellow-white LED below